When I removed these screws all at once, the little metal plate dropped down inside the camera. There are no threads on the plastic holes external to the camera. Tip #2: When removing these tine screws, there is a metal plate INSIDE the camera that screws are actually screwed into. With all the parts arrived, I took my precision phillips head screwdriver and removed the remaining two screws that were keeping the bent and broken hot shoe in place. So I ordered two new screws ($0.50 for parts + $4 S&H). They usually deal with professional repair people and it up to the caller to know the exact bits and pieces they need to order. and have no technical expertise to guide you on which parts to order. TIP #1: The Hot Shoe parts DON'T include screws! When I called back to complain about this, I was told that the people answering the phone are there to get you parts only. Based on this thread I called the Canon parts line and they identified the metal hot shoe pieces and shipped them out to me ($10 for parts + $8 for S&H. not actually replacing the metal hot shoe. Almost ALL of my searches found people focusing on tightening the tiny metal screws down. I found this thread and a few YouTube videos along with some other random descriptions of broken hot shoes. I naively thought this a ridiculous price for two little pieces of metal and a few small screws. They also told me they hadn't seen a bill come back from Canon repair for <$200. I took it to my local camera shop and was told it would cost a minimum of $125 to send the camera in to Canon for evaluation and repair. This also forceably removed two of the tiny little screws which were lost. The plastic hot shoe on the bottom of the flash broke and the metal part of my camera's hotshoe bent/broke. I had my external flash (Metz 48) attached to my camera and my wife dropped it. There is a lot of mis-information and missing steps on the internet for this repair job. I made a lot of mistakes and wanted to help anyone else who damages their Hot Shoe on their Canon 70D. Unless you've already had the board replaced, you may decide that this is a good time to replace the camera, rather than spending money to repair it.Īdding details of my journey for anyone else who stumbles along. If you search this forum, you'll discover that the 70D is prone to an expensive failure of a component on its main circuit board when it's been heavily used for video. So it's probably a good idea to send it to Canon for a complete inspection before spending any money to repair the hot shoe.īut since the camera is a 70D, there's something else you may want to consider, especially since the presence of a microphone suggests that you've been using it for video. Such damage may not be obvious to the eye and may manifest itself only in diminished image quality, less accurate focusing, etc. When a camera hits the ground that hard, you have to wonder if there is other damage, either to the camera or to the lens. Thoughts? I only use the hot shoe for mounting a mic Everything seems intacked and if I gently hold an external flash it works fine. 1screw hood fine - the others striped the plastic. Read a bit online about using a blue or purple lock tite to reattach. The hot shoe mount pulled out all 4 screws. Have a 70D that fell from my tripod with mic attached. New to the community and looking for help. Replacing assemblies takes a lot of human error out of the everyone. There are too many opportunities to introduce human error with more labor hours. Furthermore, the new assembly is likely to be more reliable than one repaired by hand. While changing out the entire assembly may seem like overkill, the labor involved in disassembling the top assembly in your camera, repairinng it, and then putting all back together again, far surpasses the costs of swapping out the assembly. In recent years, manufacturers have moved away from stocking a multitude of small parts, most of which rarely moved off of the shelf, to stocking partial assemblies that contained many of the small miscellaneous parts, such as your hot shoe. Take a careful look at the camera, and you should see that all of that stuff is attached to a single piece of body shell. If you send it in for repair, do not be surprised if the repair estimate is for a completely new top assembly, which would include LCD, hot shoe, and mode switch. You may want to explore alternative mounting options for an external microphone.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |